Features AXIOM Dual-Voltage Airpot Coffee Brewer • Easily convertible by flipping a switch to: - 120 volt, 12.5 amp - 120/208 volt, 13 amp - 120/240 volt, 15 amp • Brews 4.2 to 7.5 gallons (15.7 to 28.4 litres) of perfect coffee per hour. • For high lime areas, BrewLOGIC® technology calculates flow rate and adjusts brew time to maintain consistent pot levels. • BrewWIZARD® technology simplifies brewer programming with a LCD display. Set brew level, cold brew lock-out and tank temperature from the front of the machine. • Convenient airpots keep coffee hot and fresh for hours. • Airpots are easily transported to remote meeting rooms, breakfast bars, etc. • Brews directly into 1.9 to 3 liter airpots. • Ensures coffee brew quality with cold brew lock out capability. • Electronic diagnostics and built in tank drain make service easier. • Coffee extraction controlled with programmable pre-infusion, pulse brew and digital temperature control. • Hot water faucet. • SplashGard® funnel deflects hot liquids away from the hand. • Energy-saver mode reduces tank temperature during idle periods.
AXIOM-DV-APS with Airpot
(airpot sold separately) Dimensions: 23.6” H x 9” W x 18.5” D (59.9cm H x 22.9cm W x 47cm D)
For current specification sheets and other information, go to www.bunn.com.
Related Products Easy Clear® EQ-17-TL Product No. : 30200.1000
Universal Airpot Racks for push-button and leveraction airpots. See page A3.9 for more information. Gourmet C Funnel Product No.: 34559.0000 (7.12 inch width) 34559.0001 (7.62 inch width) • Universal design – handle may be moved to appropriate side • Allows brewing with heavier throw weights of coffee. • Paper Filter Pack Product No. : 20157.0000 Packed per case: 1,000
Brewing capacity: based upon incoming water temp of 60ºF (140ºF rise) per 1/2 gallon brew time of 4 minutes.
Electrical: If wired for 120V, requires 2-wires plus ground service rated 120V, single phase, 60 Hz. If wired for 120/208V or 120/240V, requires 3-wires plus ground service rated 120/208V or 120/240V, single phase, 60 Hz. Plumbing: 20-90 psi (138-621 kPa). Supplied with 1⁄4" male flare fitting. Tank capacity: 200 ounces (5.9 L)
13.1 GOURMET SST NARROW
Bunn-O-Matic® Corporation - 1400 Stevenson Drive Springfield, Illinois 62703 • 800-637-8606 • 217-529-6601 • Fax 217-529-6644 • www.bunn.com BUNN® practices continuous product research and improvement. We reserve the right to change specifications and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment.
Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCP/MCA pod brewers thermal servers and Thermofresh servers (mechanical and digital)- 1 year parts and 1 year labor. 2) All other equipment - 2 years parts and 1 year labor plus added warranties as specified below: a) Electronic circuit and/or control boards - parts and labor for 3 years. b) Compressors on refrigeration equipment - 5 years parts and 1 year labor. c) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis - parts and labor for 4 years or 40,000 pounds of coffee, whichever comes first. These warranty periods run from the date of installation BUNN warrants that the equipment manufactured by it will be commercially free of defects in material and workmanship existing at the time of manufacture and appearing within the applicable warranty period. This warranty does not apply to any equipment, component or part that was not manufactured by BUNN or that, in BUNN’s judgment, has been affected by misuse, neglect, alteration, improper installation or operation, improper maintenance or repair, non periodic cleaning and descaling, equipment failures related to poor water quality, damage or casualty. In addition, the warranty does not apply to replacement of items subject to normal use including but not limited to user replaceable parts such as seals and gaskets. This warranty is conditioned on the Buyer 1) giving BUNN prompt notice of any claim to be made under this warranty by telephone at (217) 529-6601 or by writing to Post Office Box 3227, Springfield, Illinois 62708-3227; 2) if requested by BUNN, shipping the defective equipment prepaid to an authorized BUNN service location; and 3) receiving prior authorization from BUNN that the defective equipment is under warranty. THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of BUNN are not authorized to make modifications to this warranty or to make additional warranties that are binding on BUNN. Accordingly, statements by such individuals, whether oral or written, do not constitute warranties and should not be relied upon. If BUNN determines in its sole discretion that the equipment does not conform to the warranty, BUNN, at its exclusive option while the equipment is under warranty, shall either 1) provide at no charge replacement parts and/or labor (during the applicable parts and labor warranty periods specified above) to repair the defective components, provided that this repair is done by a BUNN Authorized Service Representative; or 2) shall replace the equipment or refund the purchase price for the equipment. THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF THIS EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT BUNN’S SOLE OPTION AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND. In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities or services, or any other special, incidental or consequential damages. 392, A Partner You Can Count On, Air Infusion, AutoPOD, AXIOM, BrewLOGIC, BrewMETER, Brew Better Not Bitter, BrewWISE, BrewWIZARD, BUNN Espress, BUNN Family Gourmet, BUNN Gourmet, BUNN Pour-O-Matic, BUNN, BUNN with the stylized red line, BUNNlink, Bunn-OMatic, Bunn-O-Matic, BUNNserve, BUNNSERVE with the stylized wrench design, Cool Froth, DBC, Dr. Brew stylized Dr. design, Dual, Easy Pour, EasyClear, EasyGard, FlavorGard, Gourmet Ice, Gourmet Juice, High Intensity, iMIX, Infusion Series, Intellisteam, My Café, Phase Brew, PowerLogic, Quality Beverage Equipment Worldwide, Respect Earth, Respect Earth with the stylized leaf and coffee cherry design, Safety-Fresh, savemycoffee.com, Scale-Pro, Silver Series, Single, Smart Funnel, Smart Hopper, SmartWAVE, Soft Heat, SplashGard, The Mark of Quality in Beverage Equipment Worldwide, ThermoFresh, Titan, trifecta, Velocity Brew, Air Brew, Beverage Bar Creator, Beverage Profit Calculator, Brew better, not bitter., BUNNSource, Coffee At Its Best, Cyclonic Heating System, Daypart, Digital Brewer Control, Element, Nothing Brews Like a BUNN, Pouring Profits, Signature Series, Tea At Its Best, The Horizontal Red Line, Ultra are either trademarks or registered trademarks of Bunn-O-Matic Corporation. The commercial trifecta® brewer housing configuration is a trademark of Bunn-O-Matic Corporation.
INTRODUCTION This equipment will brew a ⁄2 gallon batch of coffee into an awaiting server. The brewer may have a hot water faucet for allied beverage use. It is only for indoor use on a sturdy counter or shelf. 1
USER NOTICES Carefully read and follow all notices in this manual and on the equipment. All labels on the equipment should be kept in good condition. Replace any unreadable or damaged labels.
Optional Field Wiring
Optional Field Wiring
120/208-240 V, 15.6-17.5 A, 2980-3850 W 1PH, 3-Wire + GND, 60HZ
120/208-240 V, 13.0-15.0 A, 2680-3550 W 1PH, 3-Wire + GND, 60HZ
#29710.0007 3 Warmers
To reduce the risk of electric shock, do not remove or open cover. No user-serviceable parts inside.
Authorized service personnel only. Disconnect power before servicing.
• DO NOT OVERLOAD CIRCUIT. • ALWAYS ELECTRICALLY GROUND THE CHASSIS. • DO NOT DEFORM PLUG OR CORD. • FOLLOW NATIONAL AND LOCAL ELECTRICAL CODES. • KEEP COMBUSTIBLES AWAY.
As directed in the International Plumbing Code of the International Code Council and the Food Code Manual of the Food and Drug Administration (FDA), this equipment must be installed with adequate backflow prevention to comply with federal, state and local codes. For models installed outside the U.S.A., you must comply with the applicable Plumbing /Sanitation Code for your area.
FAILURE TO COMPLY RISKS EQUIPMENT DAMAGE, FIRE OR SHOCK HAZARD.
READ THE ENTIRE OPERATING MANUAL BEFORE USING THIS PRODUCT
To reduce the risk of electric shock, do not remove or open cover. No user-serviceable parts inside. Authorized service personnel only. Disconnect power before servicing.
WA R M E R S A N D S U R FAC E S A R E H OT
ELECTRICAL REQUIREMENTS WARNING The brewer must be disconnected from the power source until specified in Initial Set-Up. Refer to Data Plate on the Brewer, and local/national electrical codes to determine circuit requirements. ELECTRICAL HOOK-UP (All Models) CAUTION – Improper electrical installation will damage electronic components. 1. An electrician must provide electrical service. 2. Determine the available on-site electrical service. 3. Select the desired unit voltage based on the available on-site electrical service. 4. Using a voltmeter, check the voltage and color coding of each conductor at the electrical source. 5. Remove the front access panel beneath the sprayhead to gain access to the terminal block. 6. Feed the supply leads through the rear of the brewer. 7. Using the above diagrams, connect the desired electrical service to the field wiring terminal block. 8. If wiring the machine for operation on 120/208 or 120/240 volts with a Power Supply Cord, the Power Supply Cord must be UL Listed Flexible Cord Type SO, SJO, SJTO, HSJO or SJOW, No. 12 AWG, 4 Conductor, Rated 90° C. Attachment Plug Cap must be UL Listed, NEMA 14-20P or L14-20P Configuration, Rated 125/250V, 20 AMPS. The Power Supply Cord must be at least 3 feet long and maximum 6 feet long (measured from Strain Relief to end of the Attachment Plug Cap). 9. Before proceeding, verify the voltage at the field wiring terminal block. 10. Set voltage switch to the appropriate position and replace the access panel. (DV Models Only) 11. If plumbing is to be hooked up later be sure the brewer is disconnected from the power source. If plumbing has been hooked up, the brewer is ready for Initial Set-Up.
• This appliance must be installed in locations where it can be overseen by trained personnel. • For proper operation, this appliance must be installed where the temperature is between 5°C to 35°C. • Appliance shall not be tilted more than 10° for safe operation. • An electrician must provide electrical service as specified in conformance with all local and national codes. • This appliance must not be cleaned by water jet. • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given instructions concerning use of this appliance by a person responsible for its safety. • Children should be supervised to ensure they do not play with the appliance. • If the power cord is ever damaged, it must be replaced by the manufacturer or authorized service personnel with a special cord available from the manufacturer or its authorized service personnel in order to avoid a hazard. • Machine must not be immersed for cleaning.
All Twins are 120/208 & 120/240V AC Single phase unless otherwise noted.
Note: Power cord must be connected to center terminal block on all Twins unless otherwise noted. Note: This electrical service requires 3 current carrying conductors (Neutral, L1 and L2) and a separate conductor for earth ground.
ELECTRICAL REQUIREMENTS Single & Dual Volt Models Requirements for brewers with an attached cord set are as follows: Note: This electrical service requires 2 current carrying conductors (Neutral, and L1) and a separate conductor for earth ground.
Dual Voltage Switch in 120V position
For Supply Connections, Use No. 12 AWG Wires Suitable For At Least 90°C (194°F) FOR USE ONLY ON AN INDIVIDUAL BRANCH CIRCUIT RATED 20 AMPS
NEUTRAL WHITE N
WHITE NEUTRAL L1 BLACK
120V 2 WIRE + GROUND 120V AC Single phase models
Requirements for brewers without an attached cord set are as follows: Dual Voltage Switch in Note: This electrical service 120/208-240V position requires 3 current carrying conductors (Neutral, L1 and L2) and a separate conductor for earth ground. 120V
For Supply Connections, Use No. 12 AWG Wires Suitable For At Least 90°C (194°F) FOR USE ONLY ON AN INDIVIDUAL BRANCH CIRCUIT RATED 20 AMPS
NEUTRAL WHITE N
NEUTRAL L1 BLACK
L1 GREEN G
120/208-240V 3 WIRE + GROUND 120/208 & 120/240V AC Single phase models
PLUMBING REQUIREMENTS These brewers must be connected to a cold water system with operating pressure between 20 and 90 psi (138 and 620 kPa) from a 1⁄2" or larger supply line. A shut-off valve should be installed in the line before the brewer. Install a regulator in the line when pressure is greater than 90 psi (620 kPa) to reduce it to 50 psi (345 kPa). The water inlet fitting is 1⁄4" flare. NOTE - Bunn-O-Matic recommends 1⁄4" copper tubing for installations of less than 25 feet and 3⁄8" for more than 25 feet from the 1⁄2" water supply line. A tight coil of copper tubing in the water line will facilitate moving the brewer to clean the counter top. Bunn-O-Matic does not recommend the use of a saddle valve to install the brewer. The size and shape of the hole made in the supply line by this type of device may restrict water flow. As directed in the International Plumbing Code of the International Code Council and the Food Code Manual of the Food and Drug Administration (FDA), this equipment must be installed with adequate backflow prevention to comply with federal, state and local codes. For models installed outside the U.S.A., you must comply with the applicable Plumbing /Sanitation Code for your area. 1. Flush the water line and securely attach it to the inlet fitting at the rear of the brewer. 2. Turn on the water supply.
INITIAL SET-UP 1. 2. 3. 4. 5.
Insert an empty funnel into the funnel rails. Place an empty server under the funnel. Connect the brewer to the power source. Turn on the main ON/OFF switch located on the left side of brewer (If equipped). Water will flow into the tank and stop when the tank is filled to its capacity. Display will show "PLEASE WAIT...TANK FILLING" until tank is filled with water. Wait approximately twenty minutes for the water in the tank to heat to the proper temperature. Display will show "READY TO BREW...WATER TEMP: 200°" when tank is at operating temperature. Some water will drip from the funnel during this time; this is due to expansion and should not occur thereafter. Place a small container beneath the faucet and open the faucet handle. Release it when you hear the tank refilling. Water volumes and flow settings have been preset at the factory. Refer to adjustments for the Set Brew Volumes section of this manual should the volume need to be increased or decreased. The brewer is now ready for use in accordance with the instructions for Coffee Brewing. Repeat steps 5-9 for remaining side on Twins.
If setting up new brewer in high mineral locations, refer to programming (Enable Brew Logic). Pertains to units with software version 1.06 & up.
Brew water temperature is factory set at 200° F (93.3° C) Areas of high altitude will require lowering this temperature to prevent boiling. This chart should be used as a guide when readjusting the brew water temperature.
OPERATING CONTROLS (A) ENABLE BREW ON/OFF SWITCH Pressing the "ENABLE BREW ON/OFF" switch (indicator on) supplies power to the brew station warmer and enables the brew circuit. Pressing the switch again (indicator off) stops brewing and de-energizes the brew station warmer. Stopping a brew cycle after it has been started will not stop the flow of water into the server until the funnel is empty. P3633
(B) BREW SWITCH Momentarily pressing and releasing the switch starts a brew cycle when the "ENABLE BREW ON/OFF" indicator is on. (C) ADDITIONAL WARMER or HALF/FULL BATCH SWITCHES Pressing any additional warmer switch so that the indicator is on, supplies power to the associated warmer. NOTE 1: APS & TC models have no warmers. NOTE 2: These switches are Half/Full Batch on "Single Axiom" models.
(D) MAIN ON/OFF SWITCH This switch, located on the left side of the brewer, turns power on and off to all components in the brewer.
COFFEE BREWING 1. Begin each brew cycle with a clean empty brew funnel. 2. Insert a BUNN filter into the funnel. 3. Pour (or grind) fresh coffee into the filter and level the bed of grounds by gently shaking. 4. Slide the funnel into the funnel rails until it stops. 5. Place an empty server under the funnel. 6. Verify that the "ENABLE BREW ON/OFF" indicator is on. 7. Momentarily press and release the "BREW" switch. The display will read "NOW BREWING", and show the time remaining in the brew cycle. 8. Following the brew, the display reads "DRIPPING" which shows the time remaining until the coffee no longer drips from the funnel tip. 9. After the coffee finishes dripping from the funnel tip, carefully remove the brew funnel and discard the grounds and filter. NOTE: Some models are equipped with a backup pour in feature, in case the plumbed water supply is disrupted. In this event, disregard steps 7-8, and pour in 64 ounces of fresh water. Page 7
CLEANING 1. The use of a damp cloth rinsed in any mild, nonabrasive, liquid detergent is recommended for cleaning all surfaces on Bunn-O-Matic equipment. 2. Check and clean the sprayhead. The sprayhead holes must always remain open. Insert the short end of the sprayhead cleaning tool into each of the five water outlets of the plastic sprayhead to remove any mineral deposits (Refer to Fig 1) 3. Insert the long end of sprayhead cleaning tool into the sprayhead fitting, and rotate several times to remove any mineral deposits from the fitting (Refer to Fig 2). NOTE: In hard water areas, this may need to be done daily. It will help prevent liming problems in the brewer and takes less than a minute. NOTE: In the event that the "Brew Logic" circuit activates (compensating for high lime build up), it will temporarily disable the "Recovery Booster" and "Pulse Brewing" systems until the unit has been de-limed. Refer to the Troubleshooting section for more details.
TANK DRAIN 1. 2. 3. 4. 5.
Loosen screws that secure the front access panel. Remove the panel. Unfasten the hose clamp at the end of the drain hose. Remove the plug. Place the end of the drain hose in a container that has a minimum capacity of 200 oz (5.9 L). Release the white clamp to drain water from the tank. When tank is empty, close the white clamp, replace the plug, and tighten the clamp at the end of the drain hose. (Repeat steps 2-5 for remaining side on Twins) 6. Replace the front panel and tighten screws.
ADJUSTMENTS & OPTIONAL SETTINGS 1
READY TO BREW WATER TEMP: 200° REAR
4 Using the menu-driven display on the front of the brewer, the operator has the ability to alter or modify various brewing parameters such as brew lockout, brew volume, brew strength, etc. This allows for the precise brewing of various flavors of coffee. Programming of the brewer is achieved by entering a certain function. Then, by the use of hidden programming switches, the operator can customize the brewing process to their specifications. PROGRAMMING SWITCHES 1. FUNCTION SCREEN This is the display which shows the various functions. 2. (Right of the display) This is used to access the program mode and is also used to step forward through the menu. 3. (Left of the display) This is used to step backwards through the function list. 4. "Digital" (lower left under the display) This is used to select options that appear on the display during programming (NO/-)
"Brewer" (center under the display) This is used to select options that appear on the display during programming (DONE)
"Control" (lower right under the display) This is used to select options that appear on the display during programming (YES/+) Page 9
(These two screens will change if "BrewLogic" is enabled) SPRAY OZ/M: (-)
CALIBRATE FLOW ? NO
BREW COUNTERS ? NO
Return To Main Screen SERVICE TOOLS ? NO
FACTORY DEFAULTS NO
Displays Model & Software Version Page 11
AXIOM BREWING & CLEANING INSTRUCTIONS BREWING
Insert a BUNN filter into the 2. funnel.
Pour in fresh coffee.
Shake funnel gently to level 4. grounds.
Slide funnel into the funnel rails of the brewer.
Place an empty decanter under 6. the funnel.
Press the “ON/OFF” switch 7. (indicator glowing).
Momentarily press and release 8. the “BREW” switch.
When brewing is complete, discard the grounds and filter.
Use a clean damp cloth rinsed 3. in mild, non-abrasive detergent to clean the sprayhead panel.
Remove the sprayhead.
Use the pointed end of sprayhead cleaning tool to remove any mineral deposits from the sprayhead openings. The sprayhead openings must always remain open.
Use the blunt end of spray- 6. head cleaning tool to clean the sprayhead outlet fitting.
Re-install the sprayhead.
Clean and sanitize the funnel. 2. NOTE: Do NOT clean this equipment with a water jet device.
NOTE: Any buildup on the sprayhead and fitting may restrict water flow, and impact your coffee brewing. For consistently great coffee, clean sprayheads and fittings weekly with sprayhead cleaning tool (#38227.0000). Upon visual inspection it may appear that light passes through all openings in the sprayhead, but a 5. thin film of residue can pass light and still impede water flow. 39645.0000A
These warranty periods run from the date of installation BUNN warrants that the ... improper maintenance or repair, non periodic cleaning and descaling, ...
BUNNlink, Bunn-OMatic, Bunn-O-Matic, BUNNserve, BUNNSERVE with the stylized .... A troubleshooting guide is provided to suggest probable causes and ...
2. SCUDERIA FERRARI WATCHES. Asserting Scuderia Ferrari's proud racing heritage and Italian pedigree, the Scuderia Ferrari Orologi collection for men,.
My Cafe AP AutoPOD w/BUNN Wrap. Product No. ... To ensure you have the latest revision of the Operating Manual, or to view the Illustrated Parts. Catalog ...
Apr 18, 2013 - Maskinens rystebord kan, nÃ¥r den er i bruk, forÃ¥rsake skade pÃ¥ grunn av styrken. Rysteplattformen bÃr derfor betjenes kun nÃ¥r maskinen stÃ¥r ...
Carefully read the instructions and safety precautions given in this manual. Do not attempt to operate this machine until you have thor- oughly read and understood the material contained in this manual and all other applicable manuals. At the time of
We will provide you with your personal release code immediately and without charge. To do this, we need the material numbers and serial numbers of the SIGMA AIR MANAGER master controller (SAM) and the SIGMA AIR CONTROL plus (SAC) air management syste
Basic Knowledge and Tools. Required. To use this manual most effectively, a general understanding of basic electrical circuits and circuit testing tools is required. You should be familiar with wiring diagrams, the meaning of voltage, ohms, amps and
G USB. H Format Switch. I MicroSD card. J Memory Status. K Door Lock. L Power Button. M Battery Status. N Update Button (hidden). Contour GPS User Manual.
stage lotteries with the reduction of compound lotteries axiom and the. (compound) independence axiom. Section three analyzes a Dutch book in support of the ...
Contact Bunn-O-Matic Corporation at 1-800-286-6070 to obtain a paper copy of ... Line, Titan, Ultra, are either trademarks or registered trademarks of Bunn-O-Matic ... This dispenser requires 2-wire, grounded service rated 208 or 240 volts ac, ...
Skyjack Service Center3451 Swenson Ave. St. Charles, Illinois, 60174 USA ...... SKYJACK warrants each new SJIII Series work platform to be free of defective ...
sebaiknya seluruh data disimpan lalu matikan peralatan. o Anda dapat menguji fungsi back-up UPS dengan memutuskan hubungan dengan jala-jala. o Jika muncul pesan âINPUT' pada display (baris kedua pada display LCD) berkedip, itu menandakan bahwa tega
8.1 Coffee and milk drinks .... ALPHAâ12CM Coffee, hot water, steam and ... Manual. Please keep the Operating Manual handy at all times. Ideally, store in a file ...
Switzerland. Since that time, VictorinoxÂ® has become known in more than ... Swiss Army Brand Watches are covered by a three-year limited warranty. Only our.
Printed in Canada. For Service in North America and Asia please call ............ 800 275-9522. Skyjack Inc. Service Center 3451 Swenson Ave,. St. Charles, IL.
US 5,170,276; DE 41 03 298 C2; EP 0 498 280 B1. Corporate Headquarters. Heidelberg Engineering GmbH â¢ Tiergartenstr. 15 â¢ 69121 Heidelberg â¢ Germany.
System menu (menu code 2)...................................................................100. 188.8.131.52.1 Brightness submenu . ..... Truck conveyor (drive 6) ..........................................................................182. 6.13.9. Fast
Skyjack Head Office 55 Campbell Rd. Guelph, Ontario NIH 189. Phone: 519-837- ... Skyjack Service Center 3451 Swenson Ave, St. Charles, Illinois, 60174 USA.
Damage to the machine and war- ranty. When using non-original capsules, dif- ferences in the brewing process and the capsule design will cause damage to the machine which means that any warranty claims may be forfeited! The manufacturer and his distr